CROWN XS-500 - limited stock

HomeDJ EQUIPMENT SALECROWN XS-500 - limited stock
HomeDJ EQUIPMENT SALECHEAP DJ GEARCROWNCROWN DJ AMPLIFIERSCrown DiscontinuedXS SeriesCROWN XS-500 - limited stock
CROWN XS-500 - limited stock
CROWN XS-500 - limited stock CROWN XS-500 - limited stock

CROWN XS-500 - limited stock

Item #: crownxs500 dj 
Rating:
REGULAR PRICE: $455.00
Availability: Usually ships the next business day
View Shipping Policy
Qty:
Price Match Request
Send Page to Friend

Discontinued DJ Equipment

Crown XS 500 Specifications


The following applies to units in Stereo mode with 8-ohm loads and rated input sensitivity unless otherwise specified.


Crown XS 500 Performance


Power Output: See power charts above. Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: ±1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5°, –18°
Signal-to-Noise Ratio:
A-weighted, below rated power: > 102 dB.
22Hz to 22kHz, below rated power: > 97 dB.
Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%.
Intermodulation Distortion (IMD):
(60 Hz and 7 kHz at 4:1) from full rated output to –40 dB: < 1%.
Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200.
Crosstalk (below rated power):
Xs500 (1 kHz, 20 kHz): > 55 dB, > 55 dB
Xs700 (1 kHz, 20 kHz): > 55 dB, > 55 dB
Xs900 (1 kHz, 20 kHz): > 67 dB, > 62 dB
Xs1200 (1 kHz, 20 kHz): >65 dB, >45 dB
Xs4300 (1 kHz, 20 kHz): > 57 dB, > 40 dB
Voltage Gain (at maximum level setting):
Xs500: 32:1 (30.1 dB)
Xs700: 38:1 (31.6 dB)
Xs900: 42:1 (32.5 dB)
Xs1200: 47.4:1 (33.5 dB)
Xs4300: 25:1 (27.8 dB)
Load Impedance: Safe with all types of loads.
Xs500, 700, 900, 1200: 2 to 8 ohms in Stereo, 4 to 8 ohms in Bridge Mono.
Xs4300: 4 to 8 ohms in Stereo, 8 ohms in Bridge Mono.
AC Line Voltage and Frequency Configurations Available (±10%): 120VAC/60 Hz and 230VAC/50 Hz.


Controls
Level: Two or four front-panel, gray rotary level controls, one for each channel.
Power: Front-panel switch; on when in the right-hand position.
Indicators
Signal: Two or four green LEDs, one for each channel, illuminates when the channel’s input signal level is above –40 dBu.
Clip: Two or four front-panel red LEDs, one for each channel, illuminates when the channel’s output signal is being overdriven.
Power: Yellow front-panel LED indicates amplifier has been turned on and AC power is available.
AC Mains: Red front-panel LED indicates the presence of AC power at the power cord, even if the amplifier is not turned on.
Fault: Red front-panel LED illuminates when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on.
Bridge: Yellow LED indicates that amplifier is in bridge mode (Channels 1 and 2, Channels 3 and 4 in Xs 4300). Temp: Red LED indicates that channel(s) are in thermal protect mode.


Input/Output
Input Connectors:
XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals.
3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals.
Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms.
Output Connectors:
Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation.
5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. Note: Binding post outputs on European models come with safety plugs installed to prevent European power-cord plugs from being inserted. The top & bottom entry positions for these connectors should therefore be used with European models. 4-Pole Speakon® output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector.
DC Output Offset (shorted input): < ±75 millivolts. Output Signal: Stereo, unbalanced, two-channel or four-channel (Xs4300 only)


Protection
Xs Series amplifiers provide extensive protection and diagnostic capabilities, including output current limiting, microprocessor-controlled DC protection, circuit breaker, and special thermal protection for the unit’s transformers.
Construction
Ventilation: Flow-through ventilation from front to back. Cooling: Internal heat sinks with forced-air cooling for rapid, uniform heat dissipation.
Air Volume Requirements (per minute per unit): 80.15 ft³ (2.27 m³).
Dimensions: EIA Standard 19-inch (48.3-cm) rack mount width (EIA RS-310-B), 3.5-inch (8.9-cm) height and 17.14-inch (43.5-cm) depth behind the mounting surface. Weight
Net Weight: 28 lb 14 oz (13.1 kg) Shipping Weight: 34 lb (15.4 kg)


Crown's Three Year, Full, No-Fault Warranty
Crown offers a Three Year, Full, No-Fault Warranty for every new Crown amplifier—an unsurpassed industry standard. With this unprecedented No-Fault protection, your new Crown amplifier is warranted to meet or exceed original specifications for the first three years of ownership. During this time, if your amplifier fails, or does not perform to original specifications, it will be repaired or replaced at our expense. About the only things not covered by this warranty are those losses normally covered by insurance and intentional abuse. And the coverage is transferable should you sell your amplifier.