QSC Amplifier Model RMX-5050 - Professional Power Amplifier - RMX Series. QSC Model RMX-5050 Now available at HollywoodDJ.

QSC Amplifier Model RMX-5050

QSC Model RMX-5050 at HollywoodDJ

The Model RMX-5050 by QSC

QSC's RMX 5050 power amplifier represents the state-of-the-art in professional quality performance at an affordable price. Perfectly suited for a wide range of sound reinforcement applications including professional touring, performing musicians, and mobile entertainers, the RMX 5050 is optimized to deliver high levels of sustained power, extraordinary audio performance and road-proven reliability.

Like its smaller sibling (the RMX 4050HD), the RMX 5050 features a three-tier, Class H design. The RMX 5050 is extremely efficient at real world power levels. Less AC current is wasted and more goes into producing useful audio power. The RMX 5050 uses the best available component upgrades to increase peak power by 25% over the RMX 4050HD.

Like all RMX amps, the RMX 5050 features balanced 1/4" TRS, XLR and barrier strip inputs, binding posts and Neutrik Speakon® outputs, front-mounted gain controls, plus signal and clip LED indicators to monitor performance.

FEATURES

The new flagship of the RMX line, the RMX 5050 provides extremely high power and represents tremendous value

The RMX 5050 provides advanced thermal performance, delivering higher continuous power in 2-ohms stereo or 4-ohms bridged applications

Dual mono, high current power supply for increased reliability and performance

3RU chassis only 16" deep

Professional quality performance - incorporates road-proven QSC designs

High-current toroidal transformers for greater two-ohm power and low noise

Independent user-defeatable clip limiters reduce distortion

Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom

Balanced 1/4" (6.3 mm) TRS, XLR, and barrier strip inputs for maximum flexibility

Binding post and Neutrik Speakon outputs

Front mounted gain controls for easy access

Signal and Clip LED indicators to monitor performance

RMX-5050 SPECIFICATIONS

8 ohms

FTC 20 Hz - 20 kHz, 0.1% THD 1050w

EIA 1 kHz, 0.1% THD 1100w

4 ohms

FTC 20 Hz - 20 kHz, 0.1% THD: 1600W

EIA 1 kHz, 0.1% THD: 1800w

2 ohms

FTC 20 Hz-20 kHz 0.1% THD: 2000w

EIA 1 kHz 1% THD 2500 W

8 ohms

FTC 20 Hz-20 kHz 0.1% THD: 3200 w

EIA 1 kHz 0.1% THD: 3600 W

4 ohms

EIA 1 kHz 1% THD: 5000 W

Distortion (SMPTE-IM): Less than 0.02%

Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power Less than 0.02%

Distortion (Typical) 1 kHz and below: full rated power Less than 0.02%

Frequency Response:

20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB

5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB

Damping Factor: Greater than 250 @ 8 ohm

Noise (unweighted): 100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)

Input Sensitivity: 1.42 Vrms for 1050 watts into 8 ohms

Voltage Gain: 64x (36 dB) for 8 ohm load

Input Impedance: 20k ohm balanced, 10k ohm unbalanced

Controls Front: AC power switch, Ch. 1 and Ch. 2 gain control

Controls Rear: 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel. Indicators

Power-On: Green LED, Protect: Red LED

Signal -30dB: Yellow LED, Clip: Red LED

Connectors Input: XLR female, TRS (1/4"), and barrier-strip screw terminals, each channel

Connectors Output: Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)

Cooling Continuously variable-speed fan, rear-to-front air flow

Amplifier Protection: Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads

Load Protection: On/off muting, DC fault output crowbar

Dimensions: 19" (48.3 cm) wide, 5.25" (13.3 cm) tall, 15.9" (40.39 cm)

Weight: 75 lbs (34.02 kg)

QSC 1 YEAR WARRANTY

We also carry QSC Model RMX-4050HD